Check out these great Mower DIY Projects. This Motor-less Mechanical Pull-Behind Mower is Made From Junk. Check out the Related Videos too...
Don
Don
11,623
724,600 views
Published on Sep 1, 2015
I made this mechanical tow behind mower for my ATV basically from junk. Although I had to buy the rear axle, a few bearings and some V-belts, this project was made from scrap metal and other recycled materials. I hope you enjoy watching!
I got the idea from a YouTube user Roadracing Mustang. His video is located at https://www.youtube.com/watch?v=99fRn.... Check it out! It's brilliant!
Soundtrack:
Demilitarized Zone (Sting) - Ethan Meixsell (YouTube Audio Library)
I got the idea from a YouTube user Roadracing Mustang. His video is located at https://www.youtube.com/watch?v=99fRn.... Check it out! It's brilliant!
Soundtrack:
Demilitarized Zone (Sting) - Ethan Meixsell (YouTube Audio Library)
My Homemade Mower
-
Category
-
License
- Standard YouTube License
- This Motorless Pull-Behind Mower is Made From Junk | Hackaday
- Mechanical Mower Made From Junk! - YouTube
- My Homemade Mower - YouTube
- HOMEMADE TOWABLE GRASS MOWING MACHINE (Also homemade ride on hedge cutter on this channel) - YouTube
- ATV trail mower project - YouTube
- ATV mower build - YouTube
- Donn DIY - YouTube
- Donn DIY - YouTube
-
-
-
Published on May 4, 2014
I built the prototype for this mower over 20 years ago out of junk lawnmower parts. It is ground powered via a 4:10 to 1 Volvo rear axle turned up 90 degrees with a pulley bolted to the driveshaft flange. The power transfers from the wheels to the driveshaft flange through a 14" pulley. It is connected by belt to a shaft with a 6" pulley on top and a 12" pulley on the bottom. That pulley drives another 6" pulley that turns the center blade. The center blade shaft drives the other two blades.
The original version was 3 push mower decks welded together with the engines replaced by some blade shafts cut from a riding mower deck. The first transfer shaft was 5/8" mounted on bushings and I didn't expect it to last two laps around the yard. I just wanted it to last long enough to see if it would actually cut grass. It held up for 4 years.
The current version is over 15 years old. I made the deck from 11 gauge (1/8") steel. All the frame work is 3" channel iron. All the shaft bearings are mounted in 1" trailer hubs. I made the shafts with 1" stainless steel. They are keyed and threaded on the blade shafts. The blades are made from 2"x1/4" flat bar. It has a 60" width cut.
The torque multiplication is reversed so it isn't good for rough terrain or heavy grass like Pensacola Bahia. It works fine on fairly level ground with centipede or other tender types of grass.
The original version was 3 push mower decks welded together with the engines replaced by some blade shafts cut from a riding mower deck. The first transfer shaft was 5/8" mounted on bushings and I didn't expect it to last two laps around the yard. I just wanted it to last long enough to see if it would actually cut grass. It held up for 4 years.
The current version is over 15 years old. I made the deck from 11 gauge (1/8") steel. All the frame work is 3" channel iron. All the shaft bearings are mounted in 1" trailer hubs. I made the shafts with 1" stainless steel. They are keyed and threaded on the blade shafts. The blades are made from 2"x1/4" flat bar. It has a 60" width cut.
The torque multiplication is reversed so it isn't good for rough terrain or heavy grass like Pensacola Bahia. It works fine on fairly level ground with centipede or other tender types of grass.
No comments:
Post a Comment