Monday, September 20, 2010
Console Record Player Retrofit
I apologize for the long gap between posts; most of my work has been proprietary recently, so there's not too much to share on the blog.
Therefore, I'm presenting a personal project: a retrofit of a late-1960s era cabinet record player. It's a Fleetwood model 4057, made in Montreal, serial 283. I came complete with AM and shortwave radio, record player and tape input, powered by a tube amp rated for 117 V, 0.95 A at the input. I believe these units were retailed by Sears. The guts were all removed and replaced by a modern turntable, digital music player, amplifier and controller.
Before the retrofit, the unit lights and tubes lit up. On radio, it crackled when you adjusted the volume but couldn't be tuned to any station. The record player wouldn't rotate and no sound was produced when the record was turned by hand. So the radio/amp was removed and sent to the tube amp hospital and the record player went to the morgue.
The first step in the retrofit was to replace the record player shelf as it had a large cutout for the sunken turntable. I took this opportunity to add some vibration isolation. I expected structural feedback to be a significant problem because the speakers and turntable are mounted in the same unit, as opposed to satellite speakers. Thus, the turntable shelf was designed to be a massive vibration isolator. The shelf is constructed of a wood frame with hardboard top and bottom panels, filled with sand.
The turntable was replaced with a Stanton T.80 turntable, capable of digital S/PDIF output.
Next: digital music. Digital music is played by a VIA Epia M10000 mainboard. This is a small form-factor (Mini-ITX) low-power computer. It's a bit underpowered for video, but is perfect for a mp3 and internet radio player. I've installed Ubuntu server and use VLC as a media player, controlled either over SSH or with its web interface.
The amplifier is an older Sony, purchased second hand for cheap. It sits in the centre cabinet. The computer provides one analog input and the turntable provides a digital input. The integrated speakers mean that the speaker cables need not be flexible after installation, so I used solid 12-gauge residential electrical cable ($1/foot at Rona for essentially no resistance and no chance of phase distortion from complex impedance). The original speakers (12-inch woofer and tweeter) haven't been replaced yet (and may not be).
Since the amp is mounted in the belly of the cabinet, the remote no longer works. I worked around this by using a microcontroller to relay the IR remote signals. There is an IR sensor behind the cloth of the right speaker, which is processed by an ATMEGA168 microcontroller. Signals destined for the amplifier (Master Volume, etc) are repeated on an IR LED temporarily taped to the amplifer's remote input. Signals that target the digital music player (track forward, etc) will be passed to the computer over USB (this functionality is not done yet). The USB link will also allow one to control the amplifier over the network. A preamp and mixer will use digital pots driven by the microcontroller to adjust the relative levels and tone of the turntable, digital music player and an aux input. This function is not yet operational, but I can dim three leds using the remote. All of this is being prototyped on an Arduino board since it has USB connectivity and there is a nice library of IR remote functions (written by Ken Shirriff).
So how does it sound? I haven't done any acoustic analysis yet and I hate audiophile-style subjective reviews, but, to my ears, it sounds really good, especially considering the vintage speakers. There is no discernible distortion at normal listening levels (as long as I remember to set the soundcard gains to avoid digital clipping).
Unfortunately, my massive sound isolator is not super effective. At high gains there is a 94.1 Hz feedback that can be eliminated if I put all my weight on the cabinet. This frequency corresponds to a 10.6 ms delay (assuming there is no signal phase changes) which at a sonic speed through wood of 3300 m/s would require a signal path of 35 m, clearly much longer than the size of the console. This leads me to believe there is a significant delay in the turntable's analog to digital conversion process. Perhaps switching to the analog output (with presumably no delay) will solve this problem, although it may just move it to a higher frequency. Alternately, the solution may be to reduce the coupling between the cabinet and the turntable shelf. The shelf is a relatively tight fit so the effective spring between the console and the shelf is relatively stiff. I plan to modify the shelf mounting so that it has no solid contact with the cabinet, being suspended on acoustic foam or a semi-liquid like acoustic caulk or Blutack.
Next: performance characterization and speaker optimization.
Edit 20/09/2009: I almost forgot to mention that I plan to host a session on microcontrollers at Bar Camp Saskatoon.
Therefore, I'm presenting a personal project: a retrofit of a late-1960s era cabinet record player. It's a Fleetwood model 4057, made in Montreal, serial 283. I came complete with AM and shortwave radio, record player and tape input, powered by a tube amp rated for 117 V, 0.95 A at the input. I believe these units were retailed by Sears. The guts were all removed and replaced by a modern turntable, digital music player, amplifier and controller.
Before the retrofit, the unit lights and tubes lit up. On radio, it crackled when you adjusted the volume but couldn't be tuned to any station. The record player wouldn't rotate and no sound was produced when the record was turned by hand. So the radio/amp was removed and sent to the tube amp hospital and the record player went to the morgue.
The first step in the retrofit was to replace the record player shelf as it had a large cutout for the sunken turntable. I took this opportunity to add some vibration isolation. I expected structural feedback to be a significant problem because the speakers and turntable are mounted in the same unit, as opposed to satellite speakers. Thus, the turntable shelf was designed to be a massive vibration isolator. The shelf is constructed of a wood frame with hardboard top and bottom panels, filled with sand.
The turntable was replaced with a Stanton T.80 turntable, capable of digital S/PDIF output.
Next: digital music. Digital music is played by a VIA Epia M10000 mainboard. This is a small form-factor (Mini-ITX) low-power computer. It's a bit underpowered for video, but is perfect for a mp3 and internet radio player. I've installed Ubuntu server and use VLC as a media player, controlled either over SSH or with its web interface.
The amplifier is an older Sony, purchased second hand for cheap. It sits in the centre cabinet. The computer provides one analog input and the turntable provides a digital input. The integrated speakers mean that the speaker cables need not be flexible after installation, so I used solid 12-gauge residential electrical cable ($1/foot at Rona for essentially no resistance and no chance of phase distortion from complex impedance). The original speakers (12-inch woofer and tweeter) haven't been replaced yet (and may not be).
Since the amp is mounted in the belly of the cabinet, the remote no longer works. I worked around this by using a microcontroller to relay the IR remote signals. There is an IR sensor behind the cloth of the right speaker, which is processed by an ATMEGA168 microcontroller. Signals destined for the amplifier (Master Volume, etc) are repeated on an IR LED temporarily taped to the amplifer's remote input. Signals that target the digital music player (track forward, etc) will be passed to the computer over USB (this functionality is not done yet). The USB link will also allow one to control the amplifier over the network. A preamp and mixer will use digital pots driven by the microcontroller to adjust the relative levels and tone of the turntable, digital music player and an aux input. This function is not yet operational, but I can dim three leds using the remote. All of this is being prototyped on an Arduino board since it has USB connectivity and there is a nice library of IR remote functions (written by Ken Shirriff).
So how does it sound? I haven't done any acoustic analysis yet and I hate audiophile-style subjective reviews, but, to my ears, it sounds really good, especially considering the vintage speakers. There is no discernible distortion at normal listening levels (as long as I remember to set the soundcard gains to avoid digital clipping).
Unfortunately, my massive sound isolator is not super effective. At high gains there is a 94.1 Hz feedback that can be eliminated if I put all my weight on the cabinet. This frequency corresponds to a 10.6 ms delay (assuming there is no signal phase changes) which at a sonic speed through wood of 3300 m/s would require a signal path of 35 m, clearly much longer than the size of the console. This leads me to believe there is a significant delay in the turntable's analog to digital conversion process. Perhaps switching to the analog output (with presumably no delay) will solve this problem, although it may just move it to a higher frequency. Alternately, the solution may be to reduce the coupling between the cabinet and the turntable shelf. The shelf is a relatively tight fit so the effective spring between the console and the shelf is relatively stiff. I plan to modify the shelf mounting so that it has no solid contact with the cabinet, being suspended on acoustic foam or a semi-liquid like acoustic caulk or Blutack.
Next: performance characterization and speaker optimization.
Edit 20/09/2009: I almost forgot to mention that I plan to host a session on microcontrollers at Bar Camp Saskatoon.
Go there...
http://blog.nutaksas.com/2010/09/console-record-player-retrofit.html
I love the old Cabinet! Beautiful wood!:) Back in about 1979, I refinished an old late 50's early 60's HiFi Cabinet. I was a Cabinet Maker at the time so this was right up my alley. I made the Turntable Pull out into a Cassette Holder. Cassettes were the current music format at the time. I put my Teac Cassette Recorder - Player in it with switches for my 4 Stereo Speakers (to turn them on and off), which I had mounted on the Walls through out my home. Originally, it was only a Mono Unit so it was not big enough to hold my Receiver - Turntable. So, I just set it on the top of the Cabinet. This worked out well since my Cabinet opened up with two doors in the front and the top was solid. It was made of Oak Plywood, with solid Oak Trim. It was a light color originally and I didn't like that at the time. So, I sanded it down and stained it with American Cherry, my favorite color to this day. I removed the Speaker and Cloth from the bottom of the Cabinet and made some Sliding Doors for that area and used the space as storage. I used it for many years, until I gave it to a friend. Minus the Stereo equipment;) He had a better setup than my old stuff anyway. By that time, the early 90's, We were both doing sound for Concerts. And he had some Small 150 Wat EV Cabs and a 1000 watt Crown Amp that we used in the house, wired directly to his 5 disk CD Player which sounded great and didn't even need an EQ (when not in use on a job). Well, Ok... So later on, I couldn't resist hooking up the Mackie Mixer and some mikes so I could practice singing too;) Then we could hook up guitars keyboards, what ever we wanted... Those EV's literally Rocked the House!;)
You really know your Audio! Great work!:) I wonder if it would be easier and work better, if you built or bought some speaker boxes and probably some newer speaker drivers to just set inside of the openings in the cabinet. You could set them on something that dampens the vibrations and maybe put something on the walls of the Cabinet too to isolate the Speaker Cabs from the Cabinet. I like the old speaker drivers too though, they usually have such a warm sound. You might try mounting them in the Speaker Boxes, if they would fit. I'm thinking, that since they are presently mounted directly to your cabined. There is a certain amount of vibration being transfered directly to the rest of the Cabinet that cannot be stopped by Dampening or Insulating the Walls or by Isolating the Turntable alone. Just one Idea...
I love to window shop on this site and use to resale though them too. I still get a little bit of a discount off of their retail prices. Don't worry I'm not trying to sell you here. Just thought you might like this site, if you don't already know about it...
http://www.parts-express.com/home-audio-video.cfm
Here's some great little Speakers, Dayton, that don't cost allot and sound great. I bought a set like this for a friend several years ago and they sound great, are very clean and that Sub can Rock the walls of his Apartment too!:) Dayton HTP-1 5.1 Home Theater Package 8" Powered Subwoofer...
http://www.parts-express.com/pe/showdetl.cfm?Partnumber=300-692
Here's the rest of their Surround Systems...
http://www.parts-express.com/wizards/searchResults.cfm?srchExt=CAT&srchCat=766
Dayton B652 6-1/2" 2-Way Bookshelf Speaker Pair. These might be ok for the job. They are on sale now for $29.00 PR Sku 300-652: http://www.parts-express.com/pe/showdetl.cfm?Partnumber=300-652
Although I would want some nice JBL, EV or Eminence Drivers, if I could afford them... heck the last time I heard a new Peavey setup, they sounded darn good too.
http://www.parts-express.com/wizards/searchResults.cfm?srchExt=CAT&srchCat=582
Speaker Building...
http://www.parts-express.com/speaker-building.cfm
Pro Audio...
http://www.parts-express.com/pro-sound.cfm
Well, guess I've thrown enough at you on this... I just love the idea of restoring old Wood and Stereos!:)
Don
No comments:
Post a Comment