I built something like this (below) in a set of Custom Cabinets. That I built in a Log Cabin. Back in the 80's. I was a Cabinet Builder. It was a narrow, but very tall Slide out Drawer. With the Racks built in for Canned Goods. It turned out very usefull, for the owner of the Cabin. Here's another versioni, that I found online...

Don

How to Build a Rotating Canned Food Shelf

Edited by Jpdunn42, Flickety, Puddy, WikiBunny and 11 others

Storing canned food in your kitchen cabinets is an inefficient use of space and you will often find old cans in the back. This easy-to-build shelf system will solve the problem by rotating the cans. The cost is a small fraction of the price of retail canned food systems. There are many variations so modify the plans to suit your needs and abilities.

Steps

1
Decide the size and number of shelves you need. This article will cover a 5-shelf system that is 32 inches wide, 24 inches deep and 64 inches tall.
2
Cut the plywood on a table saw or with a circular saw.
- Cut one full sheet in half length-wise. From each half, cut a shelf at 32 inches (should leave 64 inches for the sides).
- Cut the other full sheet in half length-wise also. Cut each half in thirds at 32 inches each.
- Cut the half-sheet of plywood at 32 inches. Cut the 32x48 piece in half (24x32). Set the remaining 16x48 piece aside for later. You should have 2-24x64 and 10-24x32.
3
Using a router and straight edge, rout slots into the sides 3/4 inch wide and 1/2 inch deep. (An alternative is to attach rails that the shelves will rest on. The slot method is stronger and will not interfere with the rolling cans.)
- The shelves need to have a 1:12 slope (1 inch drop for each 12 inches run).
- For standard cans, the distance from the top of the input shelf to the top of the corresponding output shelf is 8 inches.
- For standard cans, the distance from the top of the input shelf, to the top of the next output shelf is 4 inches.
- For standard cans, the input shelf is 3.5 inches shorter than the output shelf.
- For larger cans, add 1 inch to these dimensions.
- Draw outlines for all slots.
4
Trim the shelves. The finished outside width of the shelf system will be 32 inches. The shelves will fit in a slot 1/4 inch deep. Therefore, the width of the shelves is actually 31 inches. Each input shelf also needs to be trimmed on the back to allow a space for the can to drop. For standard cans, this gap needs to be 3.5 inches.
5
Lay one side flat on the ground with the slots facing up. Insert the shelves into the slots and place the other side on top.
6
Drive 2 inch screws through the side and into the edge of the shelf. Put two screws in each shelf.
7
Turn the unit over and drive screws in this side also.
8
Turn the unit over so the back is facing up. Attach the pieces that were cut from the input shelves to prevent the cans from falling off the back.
9
From the 16x48 scrap plywood, cut 5 pieces 2x32 inch. Turn the unit over so the front is facing up. Attach the 2x32 inch pieces to block the cans from falling out the front.
10
With the remaining plywood and/or additional scrap you have laying around, build a base that the casters will attach to. Stand the unit upright and attach it to the base.
11
Decide the configuration of cans that you need. Each row will need to be about 1/2 inch wider than the can. On the table saw, rip 1/4 inch-wide strips from plywood, MDF, or dimensional lumber. MDF and lumber work best. Attach them to the shelves with wood glue.
12
One problem you may have is the cans getting misaligned when they drop down.
- A solution for this is to add a divider connecting the row dividing strips, filling the gap. Cut cardboard in a trapezoidal shape to fit over the two row dividers. Cut out the center material of the cardboard and glue the flaps to the row dividers.
13
Another problem occurs when the gap is too large for the cans. The can can get blocked, preventing other cans from dropping down.
- A solution for this problem is to glue wedges at the back of the lower shelf. This will cause the can to roll forward before the next one locks it in. The wedges can be cut from the same material used for the row dividers. They should be large enough to move the can forward.
14
Start using the rotating canned food shelf. Add labels to the front of each row to identify the contents and load cans in the top portion of each shelf.

Video

Tips

A simpler design is possible when you have easy access to the back. This allows you to load the cans in the back and they simply roll forward.
Pre-drill your holes for the 2 inch screws by drilling a pilot hole completely through the dado (routed) slot. This was you will know exactly where to place the screws.
While stocking your shelf, organize like items by expiration date (older cans in front, newly purchased cans in back). This ensures that you're not wasting canned foods as well as saving a bit of money!
The same concepts can be applied to build this shelf system fixed in a closet. Just use rails (screwed into studs) to support the shelves.
This shelf system can accommodate any can size - even #10 cans. Just measure the diameter and length of the can and allow at least 1/2 inch clearance.
For added stability make the base larger than the footprint of the shelf unit. The casters should provide support a couple of inches in front of and behind the shelf unit.
The casters are very important. Experience has shown the mobility they add is a valuable convenience.